E-mail:Machine@chinaventech.com Expert for pre insulated duct CNC cutting machine.
1. It is strictly forbidden to wear gloves during the operation. During the operation steps, you should wear a mask and protective glasses.
2. Before use, try to carefully check the power switch, the tightness of the angle grinder, the protective cover of the angle grinder or the safety factor baffle, to ensure that the value of each prefabricated component is traceable.
Three, turn on the power switch, run a few laps with a full load, and allow it to turn on after confirming that the safety factor is accurate.
Four. The manufactured products should be clamped firmly as far as possible. It is strictly forbidden to slowly cut the product with fiber laser when the product is clamped loosely.
Fifth, the super-powerful fiber laser cutting operation process cannot be carried out. Before the fiber laser cutting, it can be carried out quickly until the maximum power of the motor is guaranteed.
Six. Fiber laser cannot be forced to cut unclamped small commodity products or aluminum alloy profiles with serious edges.
Seven. When there is any abnormal sound, turn off the power immediately, and wait for the woodworking saw blade to completely stop before checking.
8. Before repairing or disassembling parts and accessories, try to disconnect the power transformer first, and wait until the woodworking saw blade is completely stopped.
9. When the production is completed, the power is turned off, the rest or the work is left, the power should be turned off, and the mechanical equipment and nearby fields should be cleared.
1. After the automatic cutting machine equipment is completed, connect the power transformer to check whether each part of the mechanical equipment rotates flexibly and whether the standard parts are loose.
2, connect the power transformer, press the button of the host, the blade changes to whether the direction of the arrow icon is consistent. If it is reversed, adjust immediately. After checking, the rock sample can be clamped and divided. When the rock sample is clamped, reliable clamping points should be selected to avoid false clamps and false clamps. Avoid damaging the CNC tool and rock sample due to the shaking of the rock layer during the whole milling process.
3. When clamping irregular rock formations, the top pressure method can be used for clamping, and the clamping method is shown in Book 1. Clamping steps: first put the rock sample 8 flat on the ground in the work, and then insert the top pressure mobile jig tool 10 along the T-slot 3, select the interval between the jig tooling and the rock sample, and clamp the nail of the jig tooling base. Move the small chain anchor screw 13 up and down to select a reliable clamping point, then tighten the top rod moving screw cap 11, and then rotate the small chain until the small chain tops the rock sample, and tighten the small chain screw pad 12 , To prevent the small chain from loosening during the whole process of milling.
4. When slicing the core sample, if there are many rock layers, you can press several rock samples with optional long nuts and mill them together to improve the work efficiency. The clamping method is as follows As shown in Figure 2, the steps are as follows: Lay the rock sample 8 flat on the operating table 6, insert the nut and anchor screw along the T-slot 3, and insert one end of the long nut 9 into the square hole on the front vertical surface of the operating table. Rotate the adjusting screw 7 and the screw cap 10 of the nut and anchor screw to clamp the rock sample tightly. If the diameter of the core sample is slightly omitted, a thin solid wood board can be added to the rock sample so that the long nut can press the rock. Sample. This method is also used when clamping and breaking the formed square and cube rock samples.
5. When working, first run the main motor, and then press the work advance function key. When milling gradually, because the rock layers are often irregular, the cutting speed should be slow at this time, wait for the blade edge After all the rock samples are entered, you can go a little faster.
6. The automatic success-or-failure knife is cut when the machine is turned on. When the cutter moves along the operating table to the intelligent terminal, it can automatically retreat to the beginning and automatically terminate the movement. If you must go back during the whole process of work, press the fast rewind function key on the operation panel, and it will do. Always drive during fast rewinding, and press the work advance function key to start cutting. Regardless of cutting in or cutting, the cutter can be stopped moving by pressing the stop function key. When working, if you find that the cutter is too far away from the rock sample, you can press the quick release function key (according to not released) or click quick release. When the blade is close to the rock sample, the function key is released. Then press the work advance function key again to perform all normal openings. In that way, the auxiliary time of feed can be reduced.
7. When scribing the test piece, the feed speed can be adjusted according to the compressive strength of the rock layer before work. It is very likely that knife marks will appear when the feed speed is adjusted during the whole process of scribing. , When cutting harder stones based on experience, the speed is generally about 40mm/min.
Finding a reliable solution for the INFO CENTER powder coating system for sale not only supports operation of the entire system but also enhance the beauty of your workplace.
YINGDE VENTECH INTELLIGENT EQUIPMENT CO., LTD. is proud to be recognized as some of the most important and influential providers for global customers.Visit us at Ventech Automatic Machine.
There are many advantages associated with .
Quick Links
Products
Contact Us